详细化学反应机理对预混丙烷钝体熄火模拟影响

航空发动机熄火预测是重要关键问题之一，湍流和化学反应的非线性相互作用使预测非常困难。本文采用大涡模拟（LES）对湍流进行高精度模拟，采用概率密度函数输运方程湍流燃烧模型（TPDF）耦合JL4、Z66和H73三种化学反应机理，对预混丙烷钝体熄火现象和规律进行研究。JL4的反应机理最简单，反应释热快，局部放热高，火焰宽度大，火焰两侧温度梯度大，燃烧更加趋于稳定，无法模拟出熄火状态。H73机理绝热火焰温度低，火焰温度低，回流区中部OH含量高；在近熄火状态，大量CO被氧化，释放热量过高导致无法模拟出熄火现象。Z66机理可以模拟出火焰正常状态，在低当量比下也可以模拟出熄火状态。本文算例中，局部Da数大于1的区域超过35%则会发生熄火。     

高背压等离子点火器及其液体燃料点火特性实验研究

航天应用的液体火箭发动机及燃烧型加热器燃烧室室压高、燃料流量大、温度低、有重复启动需求，实现安全可靠点火的难度较大。针对这些需求，研究了一种采用高背压设计的电弧等离子体点火器。实验研究了Ar，N₂气体工质在高进气压力下的伏安特性，发现N₂在宽压力范围内适用于点火。发射光谱分析表明，在高达数MPa的进气压力下，Ar，N₂等离子体射流电子密度符合局部热力学平衡判据（LTE判据），点火能量集中。N₂等离子体整体温度低于Ar，但阳极喷口附近温度高于Ar，N₂等离子体射流火焰长，卷吸沿程空气造成射流平均温度偏低，但有助于低温液体推进剂的蒸发混合和强化点火。等离子体射流引起了臭氧和氮氧化物的形成，具有促进点火和化学反应的作用。背压提高引起电源输出电压升高，提高供气压力和电流，有助于点火器在高背压环境中稳定电压。燃烧型空气加热器燃烧室的点火实验发现，采用N₂等离子体喷注面中心点火，可以在短时间内完成酒精-空气和酒精-液氧-空气的点火，最高燃烧室室压接近5MPa时，点火器仍能稳定工作，多次使用电极烧蚀不明显，在液体火箭发动机的重复可靠点火方面具有很好的应用前景。     

拦截高速目标的比例与反比例导引捕获区分析

针对拦截高速目标的作战特点，分析了比例导引(PN)与反比例导引(RPN)的捕获区。首先，通过分析拦截弹与目标的相对运动关系，推导得到了顺轨和逆轨的零控拦截条件，此条件由目标和拦截弹的速度前置角以及二者速度比确定；其次，以拦截弹和目标速度前置角为坐标系，推导得到了PN以及RPN捕获区以及各自导航比设置范围。PN的捕获区由逆轨零控拦截条件以及与其相切且斜率为1/(N-1)的两条直线构成，RPN的捕获区由顺轨零控拦截条件以及与其相切且斜率为1/(-N-1)的两条直线构成；然后，利用函数对称性将PN与RPN捕获区转换到同一坐标区间，得到了相同条件下RPN捕获区要大于PN捕获区的结论；最后，开展了四种情形下的仿真，验证了本文捕获区分析的合理性及有效性。     

双模块下颌式内转进气道/圆锥前体一体化布局研究

为实现三维内转进气道的内收缩流场与圆锥前体的外压缩流场的良好匹配，提出了一种双模块下颌式内转进气道/圆锥前体(Double-modules Chin Inward-turning Inlet and Conical Forebody，DCII/CF)一体化设计方法，获得一种新颖的双发并置、侧向安装的DCII/CF一体化布局。针对该布局形式，开展了DCII/CF一体化构型与传统的单模块内转进气道/圆锥前体(Single-module Inward-turning Inlet and Conical Forebody，SII/CF)一体化构型的数值对比研究。结果表明：DCII/CF一体化布局不仅为内转进气道提供了优秀的前体附面层排移效果，还有效避免了传统SII/CF布局中前体附面层与进气道内部流场之间的相互干扰。在Ma∞=6.0设计状态，DCII/CF一体化布局的进气道总压恢复系数相较传统的SII/CF布局有了显著提高，从0.403提高至0.482；但由于前体附面层的排移，该布局的捕获流量略有降低， SII/CF的流量系数为0.956，该布局则为0.917。而在非设计状态，该布局形式同样具备较好的总压恢复性能，在Ma∞=5.0与Ma∞=4.0的总压恢复系数分别达到了0.586和0.682，明显高于SII/CF的总压恢复系数0.507和0.619。     

NiCrAl/Diatomite可磨耗封严涂层制备及性能

分别利用大气等离子喷涂技术制备了Ni/Al粘结底层、火焰喷涂技术制备了NiCrAl/Diatomite可磨耗封严涂层，研究了喷涂距离、送粉速率、火焰气体总流量、喷涂角度和氧燃比等喷涂参数对生长速率和涂层硬度的影响。结果表明，在较低的氧燃比条件下（O₂∶C₂H₂<1.6），随着喷涂距离的增大，涂层生长速率逐渐下降，硬度先保持不变后逐渐上升；当O₂∶C₂H₂>1.6时，涂层的生长速率会随着喷涂距离的增大先增大后减小，硬度随之逐渐下降。随着喷枪对基体相对移动速度的增大，涂层生长速率略微下降，硬度略有上升。气体总流量的增大使得涂层的生长速率明显上升，硬度明显下降。随着送粉量的增大，涂层生长速率明显提高，硬度随之先上升后下降。     

Effect of moderate geomagnetic storms on equatorial plasma bubbles over eastern Africa in the year 2012: Evolution and electrodynamics

Equatorial plasma bubbles (EPBs) are common features of the equatorial and low-latitude ionosphere and are known to cause radio wave scintillation which leads to the degradation of communication and navigation systems. Although these structures have been studied for decades, a full understanding of their evolution and dynamics remains important for space weather mitigation purposes. In this study, we present cases of EPBs occurrences around April and July 2012 geomagnetic storm periods over the African equatorial sector. The EPBs were observed from the Communications/Navigation Outage Forecasting System (C/NOFS) and generally correlated well to the ionospheric irregularities observed from the Global Positioning System total electron content (GPS-TEC) measurements (rate of TEC change, ROT). This study revealed that the evolution of the EPBs during moderate storms is controlled by the strength of the daytime equatorial electrojet (EEJ) currents regardless of the strength of the equatorial ionization anomaly (EIA), the latter is observed during the July storm case in particular. These effects were more evident during the main and part of the early recovery phases of the geomagnetic storm days considered. However, the evening hours TEC gradients between regions of the magnetic equator and ionization crests also played roles in the existence of ionospheric irregularities.     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

预测悬停旋翼跨音速流动的一种组合自由尾流/CFD方法

一种新的组合自由尾流 / CFD方法用于悬停旋翼流动的 CFD解中以考虑实际尾流的作用 .用文中描述的尾流分析方法研究了螺旋尖涡的运动 .首先从广义尾流模型开始 ,用半经验公式模化了涡核对旋翼尾流的作用 ;然后在环量收敛和尾迹收敛的条件下完成了自由尾迹计算 ;最后应用 Jameson有限体积龙格 -库塔推进格式求解了欧拉方程 .所得结果与相关文献和实验数据进行了比较     

K8、JK8机翼接头与检验量规协调准确度的提高

分析了 K8、 JL8机翼接头孔精加加后与检验量规位置协调的条件，介绍了为提高它们之间协调准确度所采取的措施及其效果。